Студопедия — Operation of the Combustion Chamber.
Студопедия Главная Случайная страница Обратная связь

Разделы: Автомобили Астрономия Биология География Дом и сад Другие языки Другое Информатика История Культура Литература Логика Математика Медицина Металлургия Механика Образование Охрана труда Педагогика Политика Право Психология Религия Риторика Социология Спорт Строительство Технология Туризм Физика Философия Финансы Химия Черчение Экология Экономика Электроника

Operation of the Combustion Chamber.






Fuel is introduced at the front end of the burner in either a highly atomized spray from specially designed nozzles, or in a prevaporized form from devices called vaporizing tubes. Air flows in around the fuel nozzle and through the first row of combustion air holes in the liner. The burner geometry is such that the air near the nozzle stays close to the front wall of the liner for cooling and cleaning purposes, while the air entering through opposing liner holes mixes rapidly with the fuel to form a combustible mixture. Additional air is introduced through the remaining air holes in the liner. The air entering the forward section of the liner tends to recirculate and move upstream against the fuel spray. During combustion this action permits rapid mixing and prevents flame blowout by forming a low-velocity stabilization zone which acts as a continuous pilot for the rest of the burner. The air entering the downstream part of the liner provides the correct mixture for combustion, and it creates the intense turbulence that is necessary for mixing the fuel and air and for transferring energy from the burned to the unburned gases. Since there are only two igniter plugs in an engine, cross ignition tubes are necessary in the can-annular types of burners in order that burning may be initiated in the other cans or inner liners. The igniter plug is usually located in the upstream reverse-flow region of the burner. After ignition, the flame quickly spreads to the primary or combustion zone where there is approximately the correct proportion of air to completely burn the fuel. If all the air flowing through the engine were mixed with the fuel at this point, the mixture would be outside the combustible limits for the fuels normally used. Therefore only about one-third to one-half is allowed to enter the combustion zone of the burner. About 25 percent of the air actually takes place in the combustion process. The gases that result from combustion have temperatures of 3560ºF (1900ºC). Before entering the turbine the gases must be cooled to approximately half this value, which is determined by the design of the turbine and the materials involved. Cooling is done by diluting the hot gases with secondary air that enters through a set of relatively large holes located toward the rear of the liner. The liner walls must also be protected from the high temperature of combustion. This is usually accomplished by introducing air at several stations along the liner, thereby forming an insulated blanket between the hot gases and the metal walls.

 

Post-Reading

I. Match parts of the sentences in columns A and B.

 

A B
1. Fuel is introduced at the front end of the burner in either 1. must also be protected from the high temperature of combustion.
2. Before entering the turbine the gases 2. the primary or combustion zone where there is approximately the correct proportion of air to completely burn the fuel.
3. The liner walls 3. the first row of combustion air holes in the liner.
4. After ignition, the flame quickly spreads to 4. the remaining air holes in the liner.
5. Air flows in around the fuel nozzle and through 5. must be cooled to approximately half this value, which is determined by the design of the turbine and the materials involved.
6. Additional air is introduced through 6.a highly atomized spray from specially designed nozzles, or in a prevaporized form from devices called vaporizing tubes.

II. a) Give the Russian equivalents to the words and word combinations from the text.

 


b) Reproduce the context.

III. Agree or disagree with the statements. Correct the wrong ones.

 

1. Fuel is introduced at the rear end of the burner in either a highly atomized spray from specially designed nozzles.

2. Air flows in around the fuel nozzle and through the last row of combustion air holes in the liner.

3. Highly pressurized gas is introduced through the remaining air holes in the liner.

4. During combustion this action permits slow mixing and prevents flame blowout by forming a low-velocity stabilization zone.

5. The air entering the downstream part of the liner provides the correct mixture for combustion.

6. Since there is only one igniter plug in an engine, cross ignition tubes are not necessary in the can-annular types of burners in order that burning may be initiated in the other cans or inner liners.

7. The igniter plug is usually located in the downstream reverse-flow region of the burner.

8. If all the air flowing through the engine were mixed with the fuel at this point, the mixture would be inside the combustible limits for the fuels normally used.

9. Before entering the turbine the gases must be cooled to approximately one third this value.

10. The liner walls must also be protected from the high temperature of combustion.

 

IV. Try to guess and explain the meaning of marked words in the text from the content.

V. a) Answer the following questions.

 

1. How is the fuel introduced to the combustion chamber?

2. What is the burner geometry?

3. What is a combustible mixture?

4. How is a flame blowout prevented?

5. What is turbulence necessary for?

6. How many igniter plugs in the combustion chamber?

7. Where are igniter plugs located?

8. When would the combustible mixture be outside the limits?

 

b) Think of three more questions and write them down.

 

VI. Retell the text.

 

Language in Use

 

I. Find pairs of synonyms among the words.

 

 

II. Find the antonyms among the words.

 


III. a)Find words in the text that mean:

 

1. A narrow part at the end of a tube through which liquid flows.

2. An occasion when a flame suddenly stops to blow.

3. Sudden violent movements of air or water.

4. Making a liquid less strong by adding water or another liquid.

5. A thick layer of something.

 

IV. Use the prepositions in the oval to complete the sentences in the text. Translate the text with the help of a dictionary in written.

 
 

 

 








Дата добавления: 2015-10-19; просмотров: 506. Нарушение авторских прав; Мы поможем в написании вашей работы!



Кардиналистский и ординалистский подходы Кардиналистский (количественный подход) к анализу полезности основан на представлении о возможности измерения различных благ в условных единицах полезности...

Обзор компонентов Multisim Компоненты – это основа любой схемы, это все элементы, из которых она состоит. Multisim оперирует с двумя категориями...

Композиция из абстрактных геометрических фигур Данная композиция состоит из линий, штриховки, абстрактных геометрических форм...

Важнейшие способы обработки и анализа рядов динамики Не во всех случаях эмпирические данные рядов динамики позволяют определить тенденцию изменения явления во времени...

Методы прогнозирования национальной экономики, их особенности, классификация В настоящее время по оценке специалистов насчитывается свыше 150 различных методов прогнозирования, но на практике, в качестве основных используется около 20 методов...

Методы анализа финансово-хозяйственной деятельности предприятия   Содержанием анализа финансово-хозяйственной деятельности предприятия является глубокое и всестороннее изучение экономической информации о функционировании анализируемого субъекта хозяйствования с целью принятия оптимальных управленческих...

Образование соседних чисел Фрагмент: Программная задача: показать образование числа 4 и числа 3 друг из друга...

Закон Гука при растяжении и сжатии   Напряжения и деформации при растяжении и сжатии связаны между собой зависимостью, которая называется законом Гука, по имени установившего этот закон английского физика Роберта Гука в 1678 году...

Характерные черты официально-делового стиля Наиболее характерными чертами официально-делового стиля являются: • лаконичность...

Этапы и алгоритм решения педагогической задачи Технология решения педагогической задачи, так же как и любая другая педагогическая технология должна соответствовать критериям концептуальности, системности, эффективности и воспроизводимости...

Studopedia.info - Студопедия - 2014-2024 год . (0.01 сек.) русская версия | украинская версия